home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
United Public Domain Gold 2
/
United Public Domain Gold 2.iso
/
utilities
/
pu429.dms
/
pu429.adf
/
Examples
/
SUP_CMD.TXT
< prev
next >
Wrap
Text File
|
1993-05-29
|
27KB
|
592 lines
******************************************
*/\><iO/X\ of PH/\TE IS Proud to Present:*
******************************************
Full AT Command Set Listing For SupraFAXModem v.32bis
NOTE: This file includes commands not available on all models & revisions.
Not all commands are available or functional in all modes & states.
AT_LIST.TXT Rev 1.7 (PHM 5/20/93) from Supra Corporation
@ Dialing Command - wait for "quiet answer"
, Dialing Command - pause (time set in S8) before finishing dialing string
! Dialing Command - hook flash (go on-hook for 700ms)
^ Dialing Command - turn on call originating tone
; Dialing Command - return to command state after dialing (last command)
+++ Default Escape Code
A Answer Phone Line
A/ Re-execute Last Command (this command NOT preceded by AT)
Bn BELL/CCITT mode switch at 300 & 1200 bps
B0=CCITT
B1=BELL (default in North America)
D Dial Command
Dials any mixed string of dialing commands and the following list of
symbols: 0123456789ABCD#*
En Command Echo
E0=not echo
E1=do echo (default)
Hn Hook Control
H0=On-Hook (Hang Up)
H1=Off-Hook (pick up phone line)
In Identification Codes
I0=SupraFAXModem product ID code
I1=ROM checksum
I2=Test Checksum (OK if correct, ERROR if not)
I3=ROM revision code
I4=Encrypted report of supported protocols
I5=Supra Copyright info.
I10=Supported Features (encoded - see end of text for listing)
L Dialing command - dials last string dialed (limitted to 40 characters)
Ln Speaker Volume
L0&L1 Low
L2 Medium (default)
L3 High
Mn Speaker Control
M0 OFF
M1 On until carrier is received (default)
M2 Always On
M3 On when answering/On only after dialing & until carrier detect
Nn Connection Rate when Originating Call
N0=Connect ONLY at rate set in S37 register
N1=Connect Normally (default)
On Return from COMMAND MODE to ONLINE state
O0=Return to ONLINE state
O1=Request a retrain & Return to ONLINE state
P Set Pulse Dialing
Qn Result Code Mode
Q0=Enabled (Default)
Q1=Disabled
Q2=Enabled when Originating, Disabled when answering
R Dialing command - reverse to answer mode after dialing
(this MUST be the last command in the dialing string)
Sr? Reports value in S register r
SCr? Reports value is SC register r
Sr=n Write value n into S register r
SCr=n Write value n into SC register r
Sx Dialing command - dials number stored in memory area x
T Set Tone Dialing
Vn Result Code mode select
V0=Numeric
V1=Verbose (default)
W Dialing command - wait for dial tone before finishing string
Wn Error Correction Result Code Selection
W0=CONNECT XXXX (DTE rate) (default)
W1=Report Error Correction Mode
W2=CONNECT XXXX (DCE rate)
Xn Dialing mode/CONNECT result codes
X0=Blind Dial (ignore Dialtone & Busy), send CONNECT
X1=Blind Dial, send CONNECT XXXX
X2=follow Dialtone, but ignore Busy, send CONNECT XXXX
X3=follow Busy, but ignore Dialtone, send CONNECT XXXX or BUSY
X4=send CONNECT XXXX, BUSY, or NO DIALTONE (default)
Yn Long Space Disconnect
Y0=Not active (default)
Y1=Active (see manual)
Zn Soft reset and Load Stored profile n (last functional command on line)
Z0=resets modem & loads stored profile 0
Z1=resets modem & loads stored profile 1
&Cn DCD signal control
&C0=DCD always on
&C1=DCD follows carrier state (ON when carrier present)
&Dn Modem reaction to DTR on to off transition greater than S25 setting
a b c d e (Settings of &Qn)
&D0= N 1 3 3 1
&D1= 2 2 3 3 2
&D2= 3 3 3 3 3
&D3= 4 4 3 3 4
List of modem reactions:
N=No Action
1=Disconnect & send OK result code
2=Swith to asynchronous command state
3=Disconnect return to command state (Answer disabled while DTR is off)
4=Perform soft reset (like ATZ0)
List of &Q states:
a. &Q0, &Q5, &Q8, or &Q9
b. &Q1
c. &Q2
d. &Q3
e. &Q4
&Fn Load Factory Default Configuration
&F0 No flow control, No error correction, No data compression
&F1 MAC hardware flow control, correction & compression active
&F2 Hardware flow control, correction & compression active
(&F2 is default for DOS, WINDOWS, AMIGA, & STAND ALONE units.)
&Jn Phone Jack Selection (&J0 is the only valid setting)
&Kn Serial Port Flow Control
&K0=None
&K3=Bidirectional Hardware (RTS/CTS)
&K4=Software (XON/XOFF)
&K5=Transparent Software flow control
&K6=Software (XON/XOFF) & Hardware (RTS/CTS) flow control
&Ln Line Type Selection (&L0 is the only valid setting)
&Mn Same function as &Qn setting.
&Pn Pulse dialing MAKE/BREAK ratio
&P0 39%/61% make/break ratio at 10PPS {US/CANADA} (Default)
&P1 33%/67% make/break ratio at 10PPS {UK/Hong Kong}
&P2 33%/67% make/break ratio at 20PPS {Japan}
&Qn Asynchronous/Synchronous Mode Selection
&Q0 Asynchronous Direct mode
&Q1 Synchronous Mode 1 (Terminal must support both modes.)
Call placed Async, modem switches to Sync. When DTR is dropped
modem returns to Async.
&Q2 Synchronous Mode 2 Modem dials number in stored location 0
when DTR goes from LOW to HIGH.
&Q3 Synchronous Mode 3 Dial number manually on a telephone, and
then bring DTR high to let the modems connect.
&Q4 Not Used
&Q5 Asynchronous Reliable Mode (most common default)
&Q6 Asynchronous Normal Mode
&Q7 Not used
&Q8 Asynchronous Reliable Mode w/o v.42/v.42bis
&Q9 Asynchronous Reliable Mode w/o MNP 2-5
&Rn RTS Synchronous Mode
&R0 CTS responds to RTS (default)
&R1 CTS always on unless &K3 is set
&Sn DSR Action Select
&S0 Always on (default)
&S1 Follows EIA specification
&Tn Modem test modes for trained technicians (you must set the serial port
at 2400 or 9600, and set the modem with AT&F0)
AT&T0 Terminate test in progress
AT&T1 Local Analog Loopback
AT&T3 Local Digital Loopback for remote modem
AT&T4 Grant request for Remote Digital Loopback (default)
AT&T5 Prohibit request for Remote Digital Loopback
AT&T6 Remote Digital Loopback
AT&T7 Remote Digital Loopback with self-test
AT&T8 Local Analog Loopback with self-test
&V Display Configuration Profiles
&Wn Write ACTIVE Profile to Stored Profile n
&W0 Writes to profile 0
&W1 Writes to profile 1
&Xn Synchronous Transmit Clock Source
&X0=Modem generated (default)
&X1=DTE supplied
&X2=Derived from the data carrier received from the remote modem.
&Yn Select Configuration Loaded at power-up
&Y0=Load profile 0 (default)
&Y1=Load profile 1
&Zx=n Write stored telephone number x (0 to 3) the number n.
\An Maximum MNP Block Size for Stream Links
\A0 64 characters
\A1 128 characters
\A2 192 characters (default)
\A3 256 characters
\Bn Transmit Break of length n x 100ms where n is 1 to 9
(Send Link Attention in MNP mode)
\Gn Modem-to-Modem XON/XOFF (software) flow control (ignored if &Q5)
\G0=Disabled (default)
\G1=Enabled
\Kn Break Processing Control (controls remote modem during MNP mode)
\K0,\K2,\K4 Enter command state without sending BREAK to remote
\K1 Clear Modem & Terminal Buffers & send BREAK to remote
\K3 Don't clear Buffers, but send BREAK to remote
\K5 Send BREAK to remote in sequence with any transmitted
data (default)
\Ln MNP Block Transfer Control
\L0 Use Stream Mode for MNP Links (default)
\L1 Use Block Mode for MNP Links
\N Operating Mode
\N0 Normal Mode
\N1 Direct Mode
\N2 MNP Reliable Mode
\N3 AutoReliable Mode
\O Originate MNP Reliable Mode Request
\Tn Set Inactivity Timer (Modem disconnects if no activity in time n)
n=0 Timer disabled (default)
n=1 to 42 Modem disconnects after n minutes without activity
\U Accept MNP Reliable Request (request must occur within 12 seconds)
\Y Switch to MNP Reliable Mode
\Z Switch from MNP to Normal Mode
%Cn MNP5 Data Compression Enable/Disable
%C0 Disabled
%C1 Enabled
%Dn BTLZ Dictionary Size
%D0=512
%D1=1024
%D2=2048 (default)
%D3=4096 (if one-way compression %M1 or %M2 is enabled)
2048 (if two-way compression %M3)
%En Auto Retrain based on line monitor readings
%E0=Disabled (Default)
%E1=Enabled
%Gn Rate Renegotiation based on line monitor readings
%G0=Disabled
%G1=Enabled (Default)
%L Reports Received Signal Level nnn in -dBm.
nnn=9 or stronger reports as 9
nnn=10 to 42 reports as value directly
nnn=43 or weaker reports as 43
%Mn BTLZ Compression Mode
%M0 Disabled
%M1 Transmit compression only
%M2 Receive compression only
%M3 Two-way compresion (default)
%P Clear Local & Remote Modems' BTLZ Dictionaries
%Q Report Received signal Quality (nnn range 0 to 127)
nnn=1 to 8 current signal quality excellent (higher rate may be used)
nnn=9 to 20 current signal good (best carrier rate for line condition)
nnn=20 to 30 current signal poor (lower carrier rate should be used)
nnn=31 to 127 signal very bad (or gone), try forcing a lower rate
NOTE: Modem uses 8 and 20 as rate renegotiation watermarks.
%Sn Set Maximum BTLZ string length n (6 to 250) (default is 32)
#CID=n Caller ID Mode
#CID=0 Disable Caller ID (Default)
#CID=1 Enable Formatted Caller ID Mode
#CID=2 Enable Raw (ASCII printable HEX number) Mode
S0=n Number of Rings to Auto Answer (0 to 255) (0 is disable & default)
S1=n Number of Rings before last answer.
S2=n Escape Code character (0 to 255) (default is 43 "+")
S3=n Carriage Return character (0-127) (default is 13)
S4=n Line Feed character (0-127) (default is 10)
S5=n Backspace character (0-32) (default is 8)
S6=n Time to Wait before Blind Dial (2-255 seconds) (default is 2)
(Applies only in X,X1, or X3 dialing mode)
S7=n Time to Wait for Carrier (1-255 seconds) (default is 50)
S8=n Pause Time for Comma Dial Command (0-255 seconds) (default is 2)
S9=n Time to Wait Before Recognizing Carrier (1-255 1/10 seconds)
(Default is 6)
S10=n Delay from Lost Carrier to Hang Up (1-255 1/10 seconds) (Default is 14)
S11=n DTMF Tone Duration/Spacing (35 to 120 1/1000 seconds) (Default is 95)
S12=n Escape Code Guard Time (0 to 255 1/50 seconds) (0 to disable, the
default is 50)
S14 Bit Mapped Option State Codes
S16 Diagnostic Test Mode setting -Bit Mapped (default 0)
0 &T1 0 Disable 1 Enable
1 Not Used
2 &T3 0 Disable 1 Enable
3 &T4/&T5 0 Off 1 In progress
4 &T6 0 Disable 1 Enable
5 &T7 0 Disable 1 Enable
6 &T8 0 Disable 1 Enable
7 Not Used
S18=n Test Mode Timer (0-255 seconds, 0=Runs endlessly)
S21 Bit Mapped Option State Codes
S22 Bit Mapped Option State Codes
S23 Bit Mapped Option State Codes
S25=n Delay to DTR (0-255 1/100 seconds, 5 default)
S26=n RTS/CTS Delay (0-255 1/100 seconds, 1 default) (Sync mode only)
S27 Bit Mapped Option State Codes
S30=n Inactivity Timer (0-255 Unit 10 seconds, 0=disable {default})
In Reliable mode any data transfer resets timer.
In Normal mode only sent data resets timer.
S36=n Negotiation Failure Treatment (0-7 7 is default)
Fallback options when S48=128 or error correction link fails:
0 Disconnect
1 Establish Direct connection
2 Undefined
3 Establish Normal connection
4 Establish a MNP connection if possible, else Disconnect
5 Establish a MNP connection if possible, else Direct connection
6 Undefined
7 Establish a MNP connection if possible, else Normal connection
S37=n Forced Single Carrier Rate (0-12 0 is default)
0 Carrier Rate at the rate the last AT command was issued.
(If rate is above highest carrier rate, then the highest
carrier rate the modem supports is used.)
1 300 bps
2-4 Undefined
5 1200 bps
6 2400 bps
7 Undefined
8 4800 bps
9 9600 bps
10 12000 bps
11 14400 bps
12 7200 bps
S38=n Delay Before Forced Disconnect (0-255 seconds, default 20)
0-254 Delay in seconds from H command, or DTR toggle ON or OFF (if
modem is set to follow DTR), before modem disconnects.
255 Modem send data out of buffer until completed or connection
is lost.
S40 Bit Mapped Option State Codes
S41 Bit Mapped Option State Codes
S46=n Protocol Selection (136 or 138) (Affects v.42/v.42bis mode)
136 Disable Compression
138 Enable Compression (default)
S48=n v.42 Negotiation (0,7,128)
0 Disable Negotiation, proceed with LAPM
7 Enable Negotiation (default)
128 Disable Negotiation, fallback per S36 setting
S80=n Enhanced Features (Bit Mapped Options)
Bit (Decimal)
0 (1) Enable Access to functions in bits 1-7 of S80
1 (2) Sync Clock Source
2 (4) Sync Clock source
3 (8) DTR/DSR always on
4 (16) Enable lease line mode (If hardware supports)
5 (32) Enable V.25bis codes
6 (64) Enable remote configuation
7 (128) Enable passwd/callback
S82=n LAPM Break Handling Options (3,7,128)
3 Expedited: Modem sends break immediately & data integrity is
maintained before and after break.
7 Destructive: Modem sends break immediately & data being
processed by each modem at that time is destroyed.
128 In sequence: Modem sends break in sequence with transmitted
data & data integrity is maintained before and after
the break
S86? Report Connection Failure Cause Code
0 Normal Disconnect (no error)
1-3 Undefined
4 Loss of Carrier
5 v.42 negotiation failed
6-8 Undefined
9 Modems could not find common protocol
10-11 Undefined
12 Normal Disconnect initiated by Remote Modem
13 Remote Modem did not respond after 10 retransmissions of
the same message
14 Protocol violation
S95=n Extended Result Code Control (default sum is 0)
Each bit set high in this register enables the corresponding result
code regardless of the W command setting.
Bit (Decimal Value)
0 (1) CONNECT XXXX result code gives DCE to DCE rate instead of
local DTE to DCE rate.
1 (2) Append /ARQ to verbose CONNECT result code if protocol is NONE
2 (4) Enable CARRIER XXXX result code
3 (8) Enable PROTOCOL XXXX result code
4 (16) Undefined
5 (32) Enable COMPRESSION result code
6 (64) Undefined
7 (128) Undefined
S109=n v.32/v.32bis Negotiation Rate Selection (default sum is 62)
Each bit set high in this register enables the corresponding rate as
a valid rate to be used during rate negotiation.
Bit (Decimal Value)
0 (1) Unused
1 (2) 4800 bps
2 (4) 7200 bps
3 (8) 9600 bps
4 (16) 12000 bps
5 (32) 14400 bps
6 (64) Unused
7 (128) Unused
S110=n v.32/v.32bis Mode & Rate Negotiation Control
0 Normal v.32 mode (no v.32bis support)
1 Normal v.32bis mode
2 v.32bis mode with automatic rate renegotiation (default)
3 v.32bis mode with automatic rate renegotiation starting with
the lowest rate set in S109 and working up one defined rate at
a time toward the highest rate set in S109 (based on %Q level
at each rate prior to stepping up.) (If the modem steps back
down, it will also follow the S109 settings.)
SCn=n BUSY Detect Watermark Controls
Each register "pair" holds the value for each setting. To set a value,
divide the setting by 256. The integer goes in the second register,
while the remained goes in the first. (A setting of 516 would convert
to 2 Remainder 4, and could be set by sending ATSC0=4SC1=2 to the
modem.) Settings are in 1/100ths of a second.
Default values:
Minimum BUSY ON Time
SC0=30
SC1=0
Maximum BUSY ON Time
SC2=75
SC3=0
Minimum BUSY OFF Time
SC4=30
SC5=0
Maximum BUSY OFF Time
SC6=75
SC7=0
(Defualts support FCC Spec. BUSY signal. Setting SC0=25 & SC4=25
allows FAST BUSY to also be detected as BUSY.)
SC8=n Set number of valid BUSY Pulses before reporting BUSY (4 is default)
FAX commands of special interest to Supra Users:
+FAE=n (CLASS 1 Only) Adaptive Answer / Silent Answer Mode Control
0 Disable Both
1 Adaptive Answer ONLY
2 Adaptive Answer & Silent Answer
3 Silent Answer ONLY
+FAA=n (CLASS 2 Only) Adaptive Answer / Silent Answer Mode Control
0 Disable Both
1 Adaptive Answer ONLY
2 Adaptive Answer & Silent Answer
3 Silent Answer ONLY
Connection Result Codes:
Nemeric Verbose
0 OK
1 CONNECT (300 bps)
2 RING
3 NO CARRIER
4 ERROR
5 CONNECT 1200
6 NO DIALTONE
7 BUSY
8 NO ANSWER
9 CONNECT 0600
10 CONNECT 2400
11 CONNECT 4800
12 CONNECT 9600
13 CONNECT 7200
14 CONNECT 12000
15 CONNECT 14400
16 CONNECT 19200
17 CONNECT 38400
18 CONNECT 57600
19 CONNECT 115200 (Not Currently Supported on MOST models)
40 CARRIER 300
46 CARRIER 1200
47 CARRIER 2400
49 CARRIER 7200
50 CARRIER 9600
51 CARRIER 12000
52 CARRIER 14400
66 COMPRESSION: CLASS 5 (MNP 5)
67 COMPRESSION: V.42BIS (BTLZ)
69 COMPRESSION: NONE
70 PROTOCOL: NONE
77 PROTOCOL: LAP-M (V.42)
80 PROTOCOL: ALT (MNP)
FAX
DATA
V.32 & V.32BIS EXTERNAL DISPLAY CODES
Red LED's
OH Off Hook
RD Receiving Data
SD Sending Data
TR Terminal Ready (Follows DTR per &Dn setting)
Green LED Display PANEL
AA Auto Answer (RI displayed during ring)
CD Carrier Detected
DC Data Compression in use
DI Dialing
FX FAX MODE
LP LAPM Error Correction in use.
M2 MNP2 Error Correction in use.
M3 MNP3 Error Correction in use.
M4 MNP4 Error Correction in use.
M5 MNP5 Data Compression in use.
OK Modem Powered Up Correctly and Ready for Use.
RE Receive Error while using LAPM or MNP mode.
RI Ring Indicator
RT Retrain in progress
TE Transmit Error while using LPAM or MNP mode.
TM Test Mode in use.
3 300 bps connection
12 1200 bps connection
24 2400 bps connection
48 4800 bps connection
72 7200 bps connection
96 9600 bps connection
120 12000 bps connection
144 14400 bps connection
Encoded Optional Feature List (ATi10)
Code Feature Added AT Commands & Result Codes
101 Fax CLASS 1 Normal CLASS 1
104 Fax CLASS 2 Normal CLASS 2
105 Fax CLASS 2.0 Normal CLASS 3
115 CCITT v.17 (14.4 Fax) See Above
120 Worldwide Support %T PTT Cert. Test Signals
*NC? Display Country Config.
*NCn Change County Config.
121 CCITT v.23 %Fn (1-3)
%F1 75T/1200R
%F2 1200R/75T
%F3 v.23 HALF DUPLEX
Adds These Result Codes:
# Text
22 CONNECT 1200TX/75RX
23 CONNECT 75TX/1200RX
44 CARRIER 1200/75
45 CARRIER 75/1200
122 CCITT v.25 See Software Doc.s
123 Blacklisting *B Display Blacklisted #'s
*D Display Delayed #'s
Adds These Result Codes:
24 DELAYED
32 BLACKLISTED
124 Access Security *C Enb. Sec. Acc. & Req.PW
*E Exit Sec. Access
*L List PW & CB directories
*P Stores PassWords
*R Request Sec. Acc. Mode
140 CCITT v.32bis (14.4 Data) See Above
141 Silent Answer See Above
142 Caller ID See Above
143 MNP 10 -B Forced FB to 1200
-C MNP10 Sync Mode
-C1 MNP10 Async Mode
-C2 MNP 2
-C3 MNP 3
-K No LAPM to MNP10 Conv.
-K1 Conv. LAPM to MNP10
-Q FB to v.22/v.22bis
-Q1 No FB to v.22/v.22bis
-Un Tx Level Change during FF
-U0 auto attn to -10dBm
-U1 auto attn to -18dBm
-U2 auto attn to -22dBm
-U3 auto attn to -25dBm
-U4 Force 2400 to -10dBm
-U5 Force 2400 to -18dBm
-U6 Force 2400 to -22dBm
-U7 Force 2400 to -25dBm
)M Tx fixed at -10dBm
)M1 Tx attempt Tx < -10dBm
*H0 Link Neg. at Top Speed
*H1 Link Neg. at 1200
*H2 Link Neg. at 4800
144 MNP "Cellular"
145 AutoSync
146 Enhanced Configuration Display \S Enhanced Display Codes
160 Voice Processing In Upgrade Doc. for Option
Call one of the PH/\TE BBS's Today!
Each one carries an extensive H/P/A Section!
!MAPHIA! [3 NODES RINGDOWN] (415)362-7463 WHQ SYSOP: BRUJJO DIHITAL'
DEVIL'S TRIANGLE (407)571-1075 USHQ SYSOP: ROLLING STONE
THE UTOPIAN ALLIANCE (301)340-3290 USHQ SYSOP: MR.OOFUS
SIN CITY +32-3825-2274 BHQ SYSOP: SINTAX
DESTINY STONE II +61-9246-3491 OZHQ SYSOP: RIPMAX
p Call Now or Be Damned
___ ___
______ Scotlands Leading BBS `/_~_\'
/___ | * +44 0592 744821 * \|(`X')|/
// < | ¯<¯~^~¯>¯
/ \ \ | ___ __ __ __ ____ ____ ¯¯U¯¯ __
< \_ / / / _/ / // // // __/ / __/ _/V\_ /.|
\ // / / / __ / // // // _/__ \ \ >. .<//`'
\_// / / / / // /| |/ // / / //¯|\ \ //<_>\X
__ / //¯ ¯¯ // / \ ¯ // ¯¯ // ¯¯ / (<mm^mm>)
| \_/ / ¯¯¯¯¯¯¯ ¯¯ ¯¯¯ ¯¯¯¯¯¯ ¯¯¯¯¯¯ ¯¯¯¯¯¯¯¯¯¯¯
\ \ = Feline Great! at 16.8 =
¯¯¯¯¯¯
p